6RA27 MANUAL PDF

Simodrive 6RA27 LIVE PLC Questions And Answers. Join Date: Nov Location: UK. Posts: 5, Here’s what one of the manuals says. List of ebooks and manuels about Simodrive 6ra27 manual – DC- Servo Simodrive 6RADV Siemens 6RA27 90 Amp DC Drive Beg. On CNC-Shopping Intl website, Buy online SIEMENS SIMODRIVE 6RA Simoreg Spindle drive control board or complete drive. Find SIEMENS SIMOREG 6RA.

Author: Dijas Grojin
Country: Kosovo
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 7 August 2017
Pages: 94
PDF File Size: 13.94 Mb
ePub File Size: 12.24 Mb
ISBN: 339-3-83964-881-2
Downloads: 97747
Price: Free* [*Free Regsitration Required]
Uploader: Nirisar

SIEMENS 6RA SIMODRIVE SIMOREG Parts

Rated motor current, armature P Suppress F with P Use of a band filter makes it possible to set a larger Kp for the speed controller without vibration occurring. The precontrol calculates the firing angle depending on the current setpoint and the EMF of the motor, uses it to compensate the above non-linearities and sets the required firing angle without delay for the following gating unit.

The software correctly sets the parameters stored on the EEPROM automatically, and sets the new parameters of the later software version to the factory setting.

Settings for armature circuit resistance and armature circuit inductance, P, P, Section 7. A temperature sensor is required for that. In such cases, only the setpoint “immediate pulse disable” via a binector settable in P can help.

Perform amnual recording with triggering in response to fault. First PZD must always be control word 1 Control Word 1 and its bit 10 11th bit because bits are counted from zero must be set to H. Please ask about permissible values. The terminal involved can be derived from r The requested torque direction is derived from the polarity of the current setpoint of connector K Calculate output voltage from delay angle r and input voltage r for calculation see below and verify voltage at 3C-3D with voltmeter; if measured output voltage shows only approx.

The physical relationship is explained below. The number of the thyristor that receives a firing pulse is set in U The point of transition from discontinuous to continuous current is influenced by the inductance in the load circuit and is approx. The following fault messages are suppressed 6r27 P in the factory setting: Sheet G and G The brush rocker must be set to the line mark on the end shield and brush rocker, if positioned incorrectly, brush sparking will result and could damage the brush and the commutator.

FAQ for 6RA70 DC MASTER and SIMOREG CM

For more manua information see description on U, Chapter 11 of the Operating Instructions. The gate pulses are formed on the CUD1, the gate pulse transformers are located on the power interface module.

Gating unit The gating unit is the interface to the power section. Protection of the motor mabual from overtemperature: Connector displays as a decimal value. In this case, P must be reduced and possibly P increased.

Products that are new, refurbished, used or for standard exchange service have been cleaned, checked and tested by our specialist technicians prior to their sale.

SIEMENS SIMODRIVE 6RA 6RA27 SIMOREG Board and Drive :

This resulting charging process is also an indication that the snubber circuit is OK, so the manifestation of this effect can also be used to manuxl the snubber circuit.

By reversing the polarity of the field current in the motor the induced motor voltage assumes negative values and the motor outputs a negative torque braking torque with constant positive current direction and negative motor voltage.

The following values can provide some orientation help: A diesel generator cannot absorb regenerative current.

After leaving the Run state, a fan after-running time which can mamual set in P factory setting 4 minutes applies. Output field current control loop firing angle, fieldSheet G Supplies 6da27 results for many normal applications. Cause Field module or CUD1. However, the 6RA70 can be used for many special applications in addition to this. Effects of the commutation notchs on loads in the same power system: Settling of a control loop on a step change in input: Connector displays as hexadecimal value.

Simodrive 6ra27 manual

If the monitoring, limitation or control features implemented in the device are deactivated, for example, by operating the device in controlled operation, this can result in additional danger for the system. Rated line voltage for converter armature P Device data and device standards: Optimization is performed based on symmetrical optimum, see below. Measurement of electrical variables Electrical variables that can be measured with a multimeter: Factory setting 5 degrees for 1Q devices.

The bridge circuit comprises two controlled valves thyristors and two uncontrolled valves diodes.