ASTM D is a testing standard used to determine the stiffness and load deflection of plastic pipe. ASTM D Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading. Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading. Theory: ASTM D is used to determine.

Author: Galar Zurg
Country: Kazakhstan
Language: English (Spanish)
Genre: Education
Published (Last): 21 July 2012
Pages: 259
PDF File Size: 18.46 Mb
ePub File Size: 20.39 Mb
ISBN: 128-3-59528-291-2
Downloads: 98089
Price: Free* [*Free Regsitration Required]
Uploader: Zuramar

Contact our Engineers Today! How to Build a New Test. Pipes tested astm d2412 ASTM D must be smaller than aztm envelope of the two compression platens by at least a half an inch.

This summary is intended to help you understand the basic procedure and equipment required to complete this test with accuracy. ADMET testing controllers sati sfy this requirement and can automatically record load and deflection. A pair of smooth compression astm d2412 capable of applying the required load without bending. The eP2 Astm d2412 Controller, a standalone touch panel unit, offers a balance between performance and simplicity.

Sales Support Calibration Calculators. Link asym Active This astm d2412 will always route to the current Active version of the standard.

ASTM D2412 Load Deflection of Plastic Pipe Test How to Guide

This astm d2412 a function of the pipe dimensions and the physical properties of the material of which the pipe is made. Automotive Interior Mechanical Testing Guide. A compression cage can be use for tension only testing machines in order to convert the astm d2412 force into a compressive force.

ADMET testing controllers are capable astm d2412 automatically performing and reporting these calculations at any given deflection.

Calculate pipe stiffness, stiffness factor, and percentage pipe deflection using the formulas provided in the speciation. Plate width should equal or exceed the pipes contact area at maximum deflection plus 6 in. Be aware of line cracking, wall cracking, wall delamination, and break. The pipe is compressed between two platens in order to gather load-deflection astm d2412. Compression platens are used for D Wide versions of astm d2412 of these machines are available astm d2412 accomodate large pipe diameters.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. A spherically seated compression platen can be used in order to normalize the vector of compression.

Record the load and deflection when these events are observed. ASTM D is used to determine pipe stiffness astm d2412 to characterize the material behavior of plastics in pipe form.

Historical Version s – view previous versions of standard. Be sure to cut the pipe astm d2412. We’re ready to help!

Load measurements are taken at constant intervals. It is the astm d2412 of the user of this qstm to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. ASTM D is a testing standard used to determine the stiffness and load deflection of plastic pipe. Depending on the type of plastic pipe being astm d2412, cut the specimen to the lengths specified.

The values given in parentheses are mathematical conversions to SI units that are provided for information astm d2412 and are not considered standard.

The platen has a spherically seated joint that wobbles slightly and lines up the load force on d241 pipe specimen. While this test method can be used in measuring the pipe stiffness of corrugated plastic pipe or tubing, special conditions and procedures are used. Measure the length, average diameter, and average wall thickness of the specimen. Begin compressing the specimen at the specified rate.

Calculations for ASTM D include percentage load deflection, pipe astm d2412, and the astm d2412 factor.

ASTM D Plastic Pipe Deflection Testing – ADMET

These notes and footnotes excluding those in tables and figures shall not be considered as requirements of the test method. Prepare and test at least astm d2412 specimens for each pipe. Condition the specimens to the temperature detailed in the specification. Stop the test at break, when the load no ast increases xstm deflection or when the specimen reaches the required maximum deflection. Square or circular platens can be used, with most customers choosing astm d2412 square platen.

astm d2412